Laser engraving machine is now used where there are many

Laser engraving machine routine maintenance methods

Laser engraving machine is now used where there are many, such as antique furniture engraving machine,wood laser engraving machine this is used in the furniture engraving machine. Laser engraving machine manufacturers are constantly developing, developing a more multifaceted laser engraving machine. Laser engraving machine also has a lot of accessories, some factory direct production, and some plants are to go to other places to purchase reprocessing. Laser engraving machine in peacetime, when maintenance is also very important. So laser engraving machine routine maintenance method is kind of how it?

Here for laser engraving machine do simple daily nurturing analysis and explanation, we usually do is look at not correct, what is not right, you need to correct. Laser engraving machine is a more sophisticated instruments and equipment that we need to be protected. Continuous running time in ten hours a day to keep following, acrylic laser engraving not over the long run. Because if laser engraving machine long run, it is easily damaged. Then life will be shortened using the. Like our people, not always work, but also need to rest.

Ensure cooling water clean, which I think we are easy to understand. Because if there are impurities in water. This will make the pump does not work properly. Or is blocked, this will cause the entire laser engraving machine was damaged. Not have water shortage phenomenon, because when the temperature at the cutting is inevitable, there is certainly friction generates heat, therefore, to prevent the water temperature is too high. Excessive temperature may also damage. Note that the above points as long as the possibility of laser engraving machine routine maintenance methods, co2 laser engraver you can extend the life of a good laser engraving machine, but also will be damaged greatly reduced.

CO2 laser machine can be used in a lot of materials, such as leather, cloth, wool, fur, acrylic, plexiglass, wooden board, plastic, resin, rubber, bamboo product, double color board, marble, paper and other non-metal materials.

Laser engraving machine operation precautions which

Laser engraving machine is useful in many fields to, in all walks of life has its place. So, we all know more or less laser engraving machine. Laser engraving machine, although there are a lot of different scope, but the principle is the same laser engraving. Laser engraving machine manufacturers are constantly blaze new trails, now has antique furniture engraving machine. So laser engraving machine handling precautions, what does? These are very complex it is not, we need to note that not a lot of it?

Now for the laser engraving machine handling precautions do some simple explanation and analysis. When using automatic measurement focus a little in need of special attention, is the automatic measurement focus Rod tightening,  if not get tight, it is easy to pre-set the laser head from the track, co2 laser engraving machine so not only can not be a good thing cut, but also be personal injury. Therefore, we use the time to be especially careful. Laser engraving machine at work, can not open the lid open, as this will affect the quality of the cutting process, it may also lead to a waste of materials. Therefore, it is to pay special attention and careful.

Laser engraving machine handling precautions are many, such as for cutting the time, must be very careful. To make the table from the workpiece holder to work together more than 2 cm, avoiding laser reflector to the rear of the workpiece damage, so things will become a waste. Therefore, these places are to pay special attention to, and if they do not attach importance to a small place, then something is wasted. But also makes laser engraving machine is damaged out. This will result in a waste of resources.

Jinan MORN Technology Co.,Ltd is located in the high-tech development zone in Jinan city, north of China. Our company is the professional manufacturer and exporter of mechanical CNC router machine, laser machine and other relevant equipment.

MORNTECH-CHINA(FACTORY)
Phone: +0086 531 66982237
Fax: +0086 531 88692337
Email: info@morntech.com
Add:High-tech development zone,Jinan city
Our cnc router website:http://www.morntech.com/

Leave a Reply

Your email address will not be published. Required fields are marked *