CO2 laser cutting machine is mainly included medium size laser machines

In the production process of the body part, the deformation of the metal parts during welding and the internal stress due to the introduction of laser cutting machine leads to the heat caused by the delay in the production process.

These deformed parts need manual correction. Laser engraver for sale In order to prove the possibility of laser cutting machine boom correction body parts, body parts of a complex line A-pillar for research.

A column by a metal plate composed of two half-shell, connected together by MIG welding and spot welding laser engraving machine. An auxiliary support tube as a supporting member between the two half-shells, which is a roll-over protection bar. The size of the free end of the two-dimensional structure deviation is produced by the mother before the column was compared. Single component due to the deformation caused by the deviation in the magnitude and direction are different. Statistics 20 parts, the number of them with the definition of the position deviation of 1 ~ 4mm.

In order to reduce distortion, wedge and plastic zone, laser irradiation method was introduced. Area and the number of correction depends on the difference in shape. Calibration results can be on-line monitoring, usually by the end of the deformation sensor parts: 10 ~ 40 times the number of laser irradiation depends on the size of the deformation. Corrected time includes a ~ 3 times of the laser radiation and measurement cycle, it normally takes 1 ~ 6min. Deformation deviation can be automatically adjusted to o2mm.

Co2 laser cutting machine CO2 laser cutting machine is mainly included medium size laser machines which can both engrave and cut on most of non metal materials, such as acrylic, wood, leather, plastic, paper, pvc, double color board, mdf, textile, glass, marble etc. But for glass and marble, laser machines can only engrave on surface of them instead of cut.

Components especially towards miniaturization of co2 laser cutting machine electronic components constantly. Component miniaturization development through special techniques, such as electronic chips in laser engraving machine lithography techniques.

Emerging issues in these areas can be achieved by improving these technologies. In addition, the processing of audio-visual equipment and hard disk read-write head electronic camera lens chip also requires a laser engraving machine molding technology. Miniaturization of these devices also requires a high accuracy of the clamping device. These often do not achieve high accuracy or very expensive. This is the key to enter the production of laser forming.

Laser cutting machine laser beam used in micro.Laser cutting machine laser beam can be focused to a very small, metal laser cutting machine so small parts microscopic adjustments are possible. And on the processing of these parts far beyond the reach of human. Laser engraving cutting machine parts processing lOum dimensions around can be achieved. This is a laser alignment and adjustment of industrial in microelectronics, micro-mechanical devices and micro-optics and optimize production conditions resigned to open new possibilities.

In order to change the bending angle of small parts made different proposals and has been implemented. Laser engraving machine calibration point heat relay mechanism is an example of an application. Laser cutting machine Non-contact spring with a certain co2 laser engraving machineposition to form a closed loop. Under the action of the laser pulse, the contact spring continuously curved until it loses the connection with the fixed contact point. This moment can be measured by a simple resistor, the use of this method allows for fine position of the contact spring so that the completion of the relay function.

In the above-mentioned method is extremely useful in many fields. In addition, the laser engraving technique can also be used for in-plane correction, for example, by adjusting the passage of the part or parts without changing their bending plane position. This idea is still in the basic research and development in the state.

Jinan MORN Technology Co.,Ltd is located in the high-tech development zone in Jinan city, north of China. Our company is the professional manufacturer and exporter of mechanical CNC router machine, laser machine and other relevant equipment.

MORNTECH-CHINA(FACTORY)
Phone: +0086 531 66982237
Fax: +0086 531 88692337
Email: info@morntech.com
Add:High-tech development zone,Jinan city
Our cnc router website:www.morntech.com

Leave a Reply

Your email address will not be published. Required fields are marked *